How To Unstick A Car Window

How to Raise a Stuck Power Window Manually in a Car

• Comment

I learned valuable DIY skills from my dad who was an electrical engineer and physicist; I took a year of auto in high school.

How to Raise a Stuck Power Window Manually

Mr Thinktank, CC BY ii.0, via flickr

Quick Fix for a Power Window That Won't Become Upwards

Did your ability window get stuck in the downward position? Are yous trying to avoid an expensive bill from the automobile-mechanic? Are you worried about leaving your window downwardly? This quick prepare will allow you lot to pull a stuck window up manually. After you get that taken intendance of, yous tin either take information technology to the mechanic or buy the replacement motor yourself for the repair.

Set a Stuck Car Window Manually

Volition Norbury

How to Fix a Stuck Car Window Manually

The principles for fixing a stuck window will exist the aforementioned or quite similar whether you accept a 2000 Toyota Camry, a 1997 Toyota 4Runner, a 2001 Mazda, or some other car model. I've had this issue with my 1997 Toyota 4Runner before. Hither's what you will need and here's what to do:

1. Remove the door panel.
2. Disconnect the window from the motor.
3. Disengage the motor.
4. Raise the window.
5. Reconnect the motor.
6. Replace the door panel.

Supplies

• Flat-head screwdriver
• Tape
• 2 Condom bands
• ii pieces of wood (approx. 12-inches in length); alternatively you can use painter'south tape

Condom

As a general word of caution, ever be careful when working with electrical equipment and wiring and wear PPE. Never attempt anything across your skill level.

Curl to Continue

Read More from AxleAddict

Step i: Remove the Door Panel

1. Remove all screws on the door console: Remove the screws on the front end of the driver'due south-side door console (they may be plastic or metallic). Be certain to locate all screws—some will be under plastic covers, behind a door handle, abreast a courtesy low-cal, etc. Remove the plastic covers during this process and set them aside. (Always put your screws in a safety place.)
2. Remove the door panel: Remove the door console using a flat-caput screwdriver by prying it gently out.
3. Disconnect the 2 plastic wire switches: You lot can employ a flat-caput screwdriver to pull the connectors apart. Put the door panel aside.
4. Remove the door panel: Using your hands or a flat-head screwdriver, gently start at the front edge of panel and pry information technology off. Piece of work your way forth the sides and to the back of the door frame. The plastic snaps should disengage. Lift the door panel off.
5. Remove the polyethylene cover: Y'all can utilize a razor blade to remove information technology instead of pealing it entirely off or just cut it along the within of the car (see the video beneath).

Step 2: Disconnect the Window From the Motor

1. Get ii pieces of wood: Get 1–2 pieces of forest (i-foot-long is fine) that volition serve as braces for holding the window in place from the inside of the door (you can too utilize painter's tape). Y'all will demand to hold the window up once you remove the screws of the regulator mechanism then that the window does not autumn off the regulator machinery.
2. Locate the regulator mechanism screws: In that location will likely be 2 screws that are holding the window to the regulator mechanism that y'all will need to remove—these are often seated and visible through the door frame. When you unscrew them, exist sure to concur the window so that it won't accidentally fall off the regulator mechanism'south ledge (this is an extra precaution).
3. Motion the window up: While holding the window in place with i hand below, grab the top of the window and pull it up as high as you can. Stick a piece of wood into the frame to concord the window in place.

Stride iii: Disengage the Motor

1. Locate the motor and remove the bolts/nuts: Find the motor in the door. It'southward often located in the elevation correct of the frame. Remove the bolts and nuts holding it in place.
2. Remove the cover: Remove the comprehend simply first secure the nuts in the base of the cover with tape (to foreclose them from getting lost) before unscrewing. The cover will have a magnetized pull when you remove it.
3. Remove the motor axle: The brushes forth the beam are jump-loaded and will pop out if the axle is removed, so use two rubber bands to hold them in place. Accept one ring and thread it through the wire that leads to the brushes; loop it back through its own finish and over a section of the regulator to secure it. Repeat this for the other brush with a 2d rubber band. You can then lift the motor axle out of the motor torso by turning it counter-clockwise. Fix it aside.

Accessing (Repairing) the Car Window Motor

Step four: Connect the Window and Motor and Raise the Window

1. Supersede the screws: While grabbing the window from above and below, replace the screws that hold the regulator machinery ledge and remove the piece of wood holding the window in identify.
2. Raise the window: While belongings the window from above and beneath, push and lift the window up; you tin can be more forceful hither while lifting to actually become the window loftier enough. Always keep your hand holding the window from below and then that the window stays up.
3. Put the motor beam back in place: Use your free hand to put the motor beam back in place into the motor body; careful not to strength it. While keeping the window in place, plough the beam clockwise to residual it into the motor trunk, keeping the brushes aligned with their original position with the commutator. Turn the axle equally far as you can (the window should be lifted up); y'all can now release both the window and the axle.
4. Supercede the motor embrace: Very carefully, replace the motor cover and be sure to listen the magnetization—do not knock the axle out of identify. Supersede the bolts.
5. Secure the motor to the door frame: Fix the motor to the door frame again by threading the bolts/nuts back in place. Y'all can tie off the wires to the door—do not reconnect them since yous're not going to use the window.

Step 5: Supervene upon the Door Panel

1. Supercede the polyethylene cover.
2. Put the door panel back. This is a multistep procedure: beginning past inserting the door handle into the console and fit the tiptop-rear edge of the door console into the top lip of the door frame. Snap the door console back into place and connect the plastic wire connectors. Yous may demand to bump the panel back into place forth the edges of the frame.
3. Replace the screws. Replace the screws that yous removed at the get-go of the project.

This article is authentic and true to the best of the author'south knowledge. Content is for advisory or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.

© 2019 Laynie H

Related Articles

How to Tell If Car Battery Is Bad

Ever wonder how to tell if car bombardment is bad? Read up and larn some tips and tricks on understanding your car battery and how to properly diagnose it.

How to Check a Auto Out Without Tools

Go through this 20-point mechanical checklist before buying a used car. These are all the things you lot'd expect your mechanic to check, but you tin easily check them yourself, and without a single tool except a torch, pen, and paper.

How to Purchase Auto Parts

The way you buy your car parts can make the deviation between getting affordable, quality parts and wasting your money and time.

Source: https://axleaddict.com/auto-repair/How-To-Raise-A-Power-Window-Manually

Posted by: johnsonolcou1989.blogspot.com

Share this post